#2355 - Tropical Storm Otto: West of Pijije, Guanacaste Province, Costa Rica - Buildings only

Please donate!
RAytoun validated #2

RAytoun validated #6

RAytoun validated #14

RAytoun validated #5

RAytoun validated #13

RAytoun validated #18

RAytoun validated #17

RAytoun validated #28

RAytoun validated #39

RAytoun validated #50

RAytoun validated #61

RAytoun validated #15

WendyNijlen marked #15 as done

geisel80 marked #16 as done

CathyO marked #14 as done

geisel80 marked #27 as done

WendyNijlen marked #61 as done

WendyNijlen marked #50 as done

geisel80 marked #38 as done

WendyNijlen marked #39 as done

This project was 100% validated outside of the Tasking Manager, all squares should be considered green

A local OSM person has contacted us and asked us to provide map data to build the OSM resources and skills in the disaster affected area. Disaster responders are using another geographic data set, we are mapping to support the local OSM community. The Costa Rica OSM Community is filled with skilled, dedicated folks who know OSM and are working to increase its usage and acceptance.

Created by bgirardot - Updated - Priority: low

  Instructions

Entities to Map
buildings only
Changeset Comment
#hotosm-project-2355 #tsotto Adding buildings in a village affected by TS Otto
When saving your work, please leave the default comment but add what you actually mapped, for example "added buildings and a residential road".

This project was 100% validated outside of the Tasking Manager, all squares should be considered green

Project Specific Mapping Notes

  • Many of these squares maybe farm or forest, please look carefully, map any buildings, but if none, just mark "Done" and select another task square.
  • Always map buildings on the edge or corner of your square, even if it goes outside your square!
  • Pick a square with no one working on a square next to if possible.
  • Default iD Bing imagery should be good, just use that.
  • Save often

Buildings

  • Please accurately outline all the buildings you can find. The outline should be for the full size of the building even if it is partly covered by trees in the imagery.
  • After drawing the outline, use the 's' key in the iD web editor to "square" the corners.
  • Many buildings are very close, but do not actually touch each other, try to map them close to each other without letting them connect or share nodes with each other, roads or residential area outlines. In the iD web editor, holding down the "alt" key will keep nodes of "snapping" to each other and accidentally connecting.
  • In the iD web editor, the first time you map a building you will use the "Building Features" category and then at the top of the list select "Building" again, this is the most generic building tag we can use as we almost never can tell the more specific use of any building from imagery alone.

General Mapping Notes

  • Be as precise as possible - This takes a little bit of practice, but following a road closely or the outline of a building carefully really makes a difference in the quality of map data produced. Quality is more important than quantity when it comes to mapping. Zooming in close helps.
  • changeset comments - These are filled in with some default information but you should always add what you mapped. For example "added buildings and roads" or "added in some waterways"
  • It is ok to "split" task squares - Sometimes a task square will have a lot detailed settlement mapping. If you think it would help to make the task square smaller so the mapping could be finished in a more reasonable time, use the "split" link above the task square comment box.
  • Personal knowledge - If you have local knowledge, that is incredibly valuable and any information you are 100% sure of you can add to the object you are mapping. Building names, health facilities, names of roads, etc, are all very valuable and the name= tag can be used to supply that information.
  • Sometimes a task square is already mapped - Sometimes you will find a task square that looks totally mapped or has nothing in it to map. Just double check that it is complete, map anything that was missed, straighten up anything that needs it and then mark it "Done".
  • Invalidated task squares - You might get a notice that a task square was "invalidated" that almost always just means someone found a few more things to map and they did not have time to map them in. No worries, it is part of the process and happens all the time. If you have to stop mapping before you have mapped everything use the "Unlock" link instead of "Done" As long as you are trying to map everything in a task square you feel confident mapping before you mark one "Done" then all is good.
  • Ask questions - if you have questions, please ask. The front page of this HOT Tasking Manager website offers a few ways to ask or if you are at a mapping event, raise your hand and ask.
  • You are making a real difference mapping - Every contribution matters in a real, tangible way. Mapping in not easy but know that your mapping is used by humanitarian organizations around the world every single day.

  Start contributing

Contributors Done Assigned